The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product selection of the complete gearbox and gear-electric motor system. Cat4CAD facilitates you in selecting and configuring the products, gives you the chance to print out extensive technical data linens, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sized sizes.
Multiple Input Options: Integral gear motors, ” or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft mounting, inch and metric result shafts, mounting pilots and flanges provide a wide selection of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or via a torque arm.
Worldwide Engine: Multiple leads and windings for globally multi volt/Hz requirements plus modular design to accept brakes, encoders or pressured cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge surface shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel helical bevel gear reducer enclosed gearing. It really is obtainable as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, face and flanged configurations. Gearmotors can be found in three stage high efficiency styles through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft options. Additionally, you will see fixed and variable velocity motors and range of ratios obtainable in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Important dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying demands of customers, we offer an array of Helical Bevel Gear Reducers. The technological content material of our products permits an extraordinary overall performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully found in a multitude of commercial and civil applications. They are B-Series units that offer excellent value for money and output torque/weight ratio, especially considering that they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with small motor, PB-fitted for motor coupling with flexible joint
Casing with feet FC, flange SC and common UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and result flanges of grey cast-iron G200 to ensure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right position helical bevel gear motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and may be offered with single or dual extended output shafts.
Devices are also available as shaft mounted or with output flanges and are designed for mounting horizontally or vertically. The units can also be provided with a bolt on torque reaction bracket and all variants are available either motorised or with an input shaft assembly.
Adding to the brand new selection of Ever-Power helical gear motors the product takes benefit of our many years of accumulated design knowledge together with the use of top quality materials and elements. The end result is a series of speed reducing geared motors providing high load transporting capacities, increased efficiency, silent running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double essential oil seals, on insight and output shaft because required.
All systems are dimensionally interchangeable with various other major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be installed with a backstop module and reducer Systems can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with small motor
Cases with ft, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and composed of Y series motor, helical gear,Arc gear and worm gear. The gears are constructed with high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi 
for gears
4: CE, ISO9001.
5: Compact design, small volume, good appearance ,and solid capacity of being overloaded.
6: Precise division and wide range for transmission ratio.
7: The effectiveness is up to as high as 96% with low energy usage, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal device, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.